Tool Heads are used in live line applications. This
equipment should be mounted on suitable handles to
ensure proper distance from live conductors. Below are
the choices of end fitings available. All tools have one of
these three fittings.
Tool Heads are used in live line applications. This
equipment should be mounted on suitable handles to
ensure proper distance from live conductors. Below are
the choices of end fitings available. All tools have one of
these three fittings.
Tool Heads are used in live line applications. This
equipment should be mounted on suitable handles to
ensure proper distance from live conductors. Below are
the choices of end fitings available. All tools have one of
these three fittings.
The Jumper Heads have a maximum opening
of 19/16” (4.0 cm) and are designed with builtin
universal joints in order to accommodate
installation lines at an angle. The jumper heads
have a quick action tightening screw for fast
closing. Threaded adapters are used to accept
5/8-11 threaded non-shrouded ferrules. A hose
clamp is included for connection strain relief.
The standard Fuse Puller heads (Cat.No. 92Q)
have plastic jaws that fit fuses from 3/4” (1.9 cm) to
2” (5.1 cm) diameter. Heads are pivotally mounted
to permit adjustment to any angle. To tighten the
jaws, just rotate the handle. The insert jaws (Cat.
No. 190NLF) for the 1-3/16” (2.1 cm) diameter
liquid filled fuse are held on the fuse puller with
springs. The attachment on the end of each fuse
puller is Cat. No. 190Q, quick change switch
hook. Other lengths available. Bag not included.
Fiberglass handle diameter: 1-1/4” (3.2cm).
The
Parallel Groove Clamp Tool
accommodates cap-screw type parallel
groove clamps (one, two, and three bolt
types). The parallel groove tool head clamps
can be installed from almost any angle by
use of the universal ball clamp. The handles
are fiberglass, with the operating handle
having a diameter of 1” (2.5 cm) and the
stationary handle 1-1/4” (3.2 cm). Bag not
included. Other lengths available.
All Insulated Adjustable Wrenches
have a spring to prevent the jaws from
accidentally moving while in use. These
wrenches have a 12” (30.5 cm) wrench
head and are supplied with a 1-1/4” (3.2
cm) diameter fiberglass handle.
Live Line Lever Cutters are compound shear cutter made from
a heat-treated alloy steel. The stationary handle is 1-1/2” (3.8 cm)
in diameter and the operating handle is 1” (2.5 cm) in diameter.
For cutting tie wires, jumper taps and conductors up to 2/0. Larger
wires should be cut with ACSR lever cutters.
Bags available. Not for use on ACSR.
Transformer Gin Assemblies are designed to lift
transformers, cross arms and other items used in pole
construction. Assembly consists of a pole with ferrules,
top fitting, center fitting, base fitting and protective bag
for the pole. Has a balanced or *unbalanced safe working
load limit of 2,500 lbs. (1,134 kgs), at a minimum of
18” apart. The working load limit (WLL) is the total
load on the gin assembly including load to be lifted, pull
on fall line and friction. Rope and block assembly not
included.
Cross Arm Gins are used on cross arms when only one
conductor needs to be raised. Use the arm gin to change
insulators; apply an armor rod to a conductor; raise a conductor
from a lower position to the cross arm, or lower the conductor.
The 2-1/2” (6.4 cm) diameter fiberglass pole has two eyes at
the top in which to hook the block line and tie back line. The
base fits a 4-3/4” x 5-7/8” (12.1 x 14.9 cm) cross arm. Included
shims are needed for smaller arms.
Ground Rod Drivers are 60” (1.52 m) long and drives
5/8” (1.6 cm) ground rods deep by concentrating impact
directly to the rod.
Light-weight and easy-to-use. Drives 1/2” (1.3 cm) ground
rods with less effort than conventional methods. Discs
surrounding the handle protect hands from walls, shrubbery,
and the sliding parts. Measures 26” (66 cm) long with a 14”
(35.6 cm) stroke.
The Temporary Transfer Arm is used to change crossarms,
insulators, or poles on short spans up to and including 15 kV phase
to phase. The mast (Cat. No. 1306M) is 2-1/2” in diameter by 6 feet
(1.82 m) long. The horizontal arm (Cat. No. 1340WHF8) is 2-1/2” in
diameter by 8 feet (2.44 m) long. The arm has a balanced load rating
of 600 lbs. (272 kgs); unbalanced at 150 lbs. (68 kgs). These units
are mounted to the pole using chain binders (Cat. No. 1304D) and
are rated for 15 kV without insulators and 35 kV with insulators.